|
|
 |
|
|
Electrical Specifications
|
Power supply |
Rated input voltage |
12 to 24Vdc |
|
Input voltage limits |
10.8 to 28.8Vdc |
|
Voltage drop |
12 Vdc: 2.5 ms or less
24 Vdc: 10 ms or less |
|
Power consumption (primary power supply including power loss) |
Backlight ON: 100% (Power is supplied to external devices) |
21W or less |
Backlight ON: 100%
(Power is not supplied to external devices) |
18W or less |
|
Backlight adjusted: 20% (Power is not supplied to external devices) |
11W or less |
Backlight OFF
(Power is not supplied to external devices) |
8W or less |
|
In-rush current |
30 A or less |
|
Voltage endurance |
1,000 Vac, 20 mA for 1 minute (between charging and FG terminals) |
|
Insulation resistance |
500 Vdc, 10 MΩ or more (between charging and FG terminals) |
Environmental Specifications
|
International Safety Standards |
 |
|
Physical environment |
Surrounding air temperature |
0 to 60 ℃ (32 to 140 ℉) |
|
Storage temperature |
-20 to 60 ℃ (-4 to 140 ℉) |
|
Surrounding air and storage humidity |
10% to 90% RH (non-condensing, wet bulb temperature 39 ℃
[102.2 ℉] or less) |
|
Dust |
0.1mg/m3 (10-7 oz/ft3) or less (non-conductive levels) |
|
Pollution degree |
For use in Pollution Degree 2 environment |
|
Corrosive gases |
Free of corrosive gases |
|
Atmospheric pressure (operating altitude) |
800 to 1,114hPa (2,000 m [6,561 ft] or lower) |
|
Mechanical environment |
Vibration resistance |
IEC/EN 61131-2 compliant
5 to 9 Hz single amplitude 3.5 mm (0.14 in)
9 to 150 Hz fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.) |
|
Shock resistance |
IEC/EN 61131-2 compliant
147 m/s2, X, Y, Z directions for 3 times |
|
Electrical environment |
Noise immunity |
Noise voltage: 1,000 Vp-p
Pulse duration: 1 μs
Rise time: 1 ns
(via noise simulator) |
|
Electrostatic discharge immunity |
Contact discharge method: 6 kV (IEC/EN 61000-4-2 Level 3) |
Structural Specifications
|
Grounding |
Functional grounding: Grounding resistance of 100Ω, 2 mm2 (AWG 14) or thicker wire, or your country’s applicable standard (same for FG and SG terminals). |
|
Cooling method |
Natural air circulation |
|
Structure *1 |
When using a factory-installed front USB cover: IP65F, IP67F, Type 1
When using a front USB cover as an option: IP66F, IP67F, Type 1, Type 4X (Indoor
Use Only)/13
NOTE: The option is a front USB cover with screw manufactured by Pro-face (Model Number PFXZCDCVUS1). |
|
External dimensions |
W397 x H296 x D67 mm (W15.6 x H11.7 x D2.64 in.) |
|
Panel cut dimensions |
W383.5 x H282.5 mm (W15.1 x H11.12 in.) *2
Panel thickness area: 1.6 to 5 mm (0.06 to 0.2 in) *3 |
|
Weight |
5.2 kg (11.5 lb) or less |
-
*1 The front face of this product, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though this product's level of resistance is equivalent to these standards, oils that should have no effect on this product can possibly harm this product. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to this product for long periods of time. If this product's front face protection sheet peels off, these conditions can lead to the ingress of oil into this product and separate protection measures are suggested.
Also, if non-approved oils are present, they may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing this product, be sure to confirm the type of conditions that will be present in this product's operating environment. If the installation gasket is used for a long period of time, or if this product and its gasket are removed from the panel, the original level of protection cannot be kept. To maintain the original protection level, be sure to replace the installation gasket regularly.
-
*2 For dimensional tolerance, everything +1/-0 mm (+0.04/-0 in.) and R in angle are below R3 (R0.12 in).
-
*3 Even if the installation wall thickness is within the recommended range for the panel cut dimensions, depending on wall's material, size, and installation location of this product and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.
Display Specifications
|
Display type |
TFT Color LCD |
|
Display size |
15-inch |
|
Resolution |
1,024 x 768 pixels (XGA) |
|
Effective display area |
W304.1 x H228.1 mm (W11.97 x H8.98 in.) |
|
Display colors |
16 million colors |
|
Backlight |
White LED (Not user replaceable. When replacement is required, contact your local distributor.) |
|
Backlight service life |
50,000 hours or more (continuous operation at 25℃ [77℉] before backlight brightness decreases to 50%) |
|
Brightness control |
0 to 100 (Adjusted with the launcher) |
|
Brightness sensor |
equipped |
Touch Panel
|
Type |
Resistive film (analog, multi-touch) |
|
Interface |
USB 2.0 (Type B) *1 |
|
Service life |
1 million times or more |
-
*4 For the detail, see the interface specifications.
Interface Specifications
|
USB (Type A) interface |
Connector |
Front side: USB 2.0 (Type A) x 1 |
|
Power supply voltage |
5 Vdc ±5% |
|
Maximum supply current |
500 mA |
|
Maximum transmission distance |
5 m |
|
USB (Type B) interface |
Connector |
USB 2.0 (Type B) x 1 |
|
Maximum transmission distance |
5 m |
|
Video interface *1 |
DVI-D |
DVI-D input |
|
Connector |
DVI-D 24 pin (socket) x 1 |
|
Maximum transmission distance |
5 m |
-
*5 Different formats can be used by using conversion adapters and cables.
External Dimensions
Panel Cut
|
A |
B |
C |
383.5 mm (+1/-0 mm)
(15.1 in. [+0.04/-0 in.]) |
282.5 mm (+1/-0 mm)
(11.12 in. [+0.04/-0 in.]) |
1.6 to 5 mm
(0.06 to 0.2 in.) |
Dimensions with Cables
*1 Rotation area of the fastener
*2 Pitch of the center of installation fastener screws |
|
|
|
|
|
|
|
