 |
|
|
5.7-inch Controller
Input Specifications
|
Rated Voltage |
DC24V |
|
Maximum Allowable Voltage |
DC28.8V |
|
Input Method |
Sink/ Source Input |
|
Rated Current |
6.5mA (DC24V) (IN0, IN2, IN4, IN6)
4.1mA (DC24V) (Other inputs) |
|
Input Resistance |
Approx. 3.7kΩ (IN0, IN2, IN4, IN6)
Approx. 5.9kΩ (Other inputs) |
|
Input Points |
16 points |
|
Common Lines |
1 |
|
Common Design |
16 points/ 1 common line |
|
Operation Range |
ON Voltage |
DC19V or more |
|
OFF Voltage |
DC5V or less |
|
Input Delay Time |
OFF→ON |
0.5 to 20ms *1 |
|
ON→OFF |
0.5 to 20ms *1 |
|
Input Signal Display |
No LED indicators |
|
Insulation Method |
Photocoupler isolation |
|
External Connection |
38-pin connector (used with Output section) |
|
External Power Supply |
For Signal: DC24V |
Output Specifications
|
|
OUT0 to OUT3 |
OUT4 to OUT15 |
|
Rated Voltage |
DC24V |
|
Allowance Voltage Range |
DC20.4V to DC28.8V |
|
Output Method |
Sink Output |
LT3300-S1-D24-K, LT3300-L1-D24-K, LT3301-L1-D24-K |
|
Source Output |
LT3300-S1-D24-C, LT3300-L1-D24-C, LT3301-L1-D24-C |
|
Maximum Load Voltage |
200mA/1point, 1.6A/1 common |
|
Minimum Load Current |
1mA |
1mA
(Pulse/ PWM Output Unavailable) |
|
Output Voltage Drop |
DC0.5V or les |
|
Output Delay Time |
OFF→ON |
5µs or less
(at Output DC24V, 200mA) |
0.5m or less
(at Output DC24V, 200mA) |
|
ON→OFF |
5µs or less
(at Output DC24V, 200mA) |
0.5ms or less
(at Output DC24V, 200mA) |
|
Voltage Leakage (When OFF) |
0.1mA or less |
|
Clamp Voltage |
39V ±1V |
|
Type of Output |
Transistor Output |
|
Common Lines |
2 |
|
Common Design |
8 points/ 1 common line × 2 |
|
External connection |
38-pin connector (also used for Input) |
|
Output Protection Type |
Output is unprotected |
|
Internal Fuse |
2.5A, 125V Chip fuse × 2 (not replaceable) |
|
Surge Control Circuit |
Zener diode |
|
Output points*1 |
16 points |
|
Input Signal Display |
No LED indicators |
|
Isolation Method |
Photocoupler Isolation |
|
External Power Supply |
For Signal: DC24V |
High-speed Counter/ Pulse Catch Input Specifications
|
|
High-speed Counter |
Pulse Catch Input |
|
Input *1 |
DC24V Open collector |
DC24V
Open collector |
|
Single phase (4 points) |
Double phase
(1 point or 2 points) |
|
Input Points |
CT0(IN0),
CT1(IN2),
CT2(IN4),
CT3(IN6)
defined by user |
CT0(IN0), CT1(IN2) (used as pair)
CT0: A phase, CT1: B phase
CT2 (IN4), CT3 (IN6)
CT3: Phase A, CT3: Phase B
defined by user |
IN0, IN2, IN4, IN6
defined by user |
Minimum Pulse Width
(Pulse Input) |
|
|
|
Count Speed
(Rise, Fall Time)
|
|
-
|
|
Phase |
1 phase |
90 degree-phase differentional 2-phase signal / 1-phase + directional signal |
-
|
|
High Speed Count Frequency |
100Kpps |
50Kpps |
-
|
|
Count Edge Designation |
Available |
Not available |
-
|
|
Count Register |
32-bit UP/ DOWN counter |
-
|
|
Counter Mode Charge |
Set through software |
-
|
|
Upper/ Lower Limit Settings |
Not available |
-
|
|
Preload/Prestrobe |
Available |
-
|
Marker Input
(Clear Counter Value) |
None |
IN3, IN7 |
-
|
Pulse/ PWM Output Specifications
|
|
Pulse output |
PWM output |
|
Output Points*1 |
4 points |
|
Output Method |
PLS0 to PLS3
(OUT0 to OUT3)
defined by user |
PWM0 to PWM3
(OUT0 to OUT3)
defined by user |
|
Load Voltage |
DC24V |
|
Minimum Load Current |
1mA |
|
Maximum Output Frequency |
Up to 65kHz possible per point (set through software)
Varies depending on the number of CH of High-speed counter, pulse output. |
|
Pulse Acceleration Deceleration Speed |
Available |
Not available |
|
ON Duty |
50% ± 10% (at 65kHz)*2 |
19 to 81% (at 65kHz)*3 |
-
*1 Digital filter can be set intervals of 0.5ms.
-
*2 The ON Duty error (10%) will be reduced if the Output frequency is low.
-
*3 ON duty (effective range) increases as the output frequency setting is lower.
|
|
|
|
|
|
|
|
|
Specification of LT3201-A1-D24-K
LT-3201A SinkOutput type
Model: LT3201-A1-D24-K
Monochrome LCD (Amber/Red) (8 Shades) / QVGA
Functional Specification
|
Display Type |
STN Color LCD |
|
Display Size |
5.7" |
|
Resolution |
320 x 240 pixels (QVGA) |
|
Dot pitch |
W0.36 x H0.36 mm [W0.01 x H0.01 in.] |
|
Effective Display Area |
W117.2 x H88.4 mm [W4.61 x H3.48 in.] |
|
Display Colors |
4,096 Colors |
|
Backlight |
White LED (User nonreplaceable parts. Factory replacement required.) |
|
Brightness Control |
8 Levels (Adjusted with the touch panel) |
|
Contrast Control |
8 Levels (Adjusted with the touch panel) |
|
Backlight Service Life |
50,000 hrs. or more (continuous operation at 25℃ before backlight brightness decreases to 50%) |
|
Language Fonts |
Japanese: 6,962 (JIS Standards 1 & 2) (including 607 non-kanji characters), ANK: 158 (Korean fonts, Simplified Chinese and Traditional Chinese fonts are downloadable. |
|
Character Sizes |
Standard font: 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts, Stroke font: 6 to 127 pixel fonts, Image font: 8 to 72 pixel fonts |
|
Font Sizes |
Standard font: Width can be expanded up to 8 times. Height can be expanded up to 8 times.*1 |
|
Text |
8 x 8 dots |
40 char. x 30 rows |
|
8 x 16 dots |
40 char. x 15 rows |
|
16 x 16 dots |
20 char. x 15 rows |
|
32 x 32 dots |
10 char. x 7 rows |
|
Control Memory |
Variable Area |
SRAM 64 KB (uses lithium battery) |
|
Program Area |
FLASH EPROM 132 KB |
|
Number of Step |
Equivalent to 15,000 steps*2 |
|
Application Memory |
FLASH EPROM 6 MB*3 |
|
Data Backup |
SRAM 128 KB (Lithium battery for backup memory) |
|
Clock Accuracy |
±65 sec/month (deviation at room temperature and power is OFF)*4 |
|
Touch Panel Type |
Resistive Film (analog) |
|
Touch Panel Resolution |
1,024 x 1,024 |
|
Touch Panel Service Life |
1,000,000 times or more |
|
Interface |
Serial (COM1) |
RS-232C/422/485, Asynchronous Transmission, Data Length: 7 or 8 bit, Parity: none, Even or Odd, Stop Bit: 1 or 2 bit, Data Transmission Speed: 2,400 bps to 115.2 kbps, Connector: D-Sub9 (plug) |
|
Ethernet (LAN) |
IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX, Connector: Modular jack (RJ-45) x 1 |
|
USB (TYPE-A) |
Conforms to USB1.1 (TYPE-A) x 1, Power Supply Voltage: DC 5 V ±5 %, Output Current: 500 mA or less, Communication Distance: 5 m or less |
|
AUX/Expansion Unit |
Communication Expansion Unit x 1*5 |
|
Control |
DIO (Source Type) |
16-Point Input Sink Source, , 16-Point Output Source, Connector: 38pin |
-
*1 Other font sizes can be set up with the Editor software.
-
*2 Up to 60,000 steps can be converted in software. However, this reduces internal memory capacity (for screen data) by 1 MB.
-
*3 Capacity available for user application.
-
*4 Depending on the operating temperature and age of unit, the clock can deviate from -380 to +90 sec/month. For systems where this level of deviation is a problem, the user should monitor and make adjustments when required.
-
*5 EX Module and Communication Expansion Unit cannot be used at the same time.
General Specification
|
International Safety Standards |
|
|
Rated Input Voltage |
DC 24 V |
|
Input Voltage Limits |
DC 19.2 to 28.8 V |
|
Allowable Voltage Drop |
3 ms or less |
|
Power Consumption |
27 W or less |
|
In-Rush Current |
30 A or less |
|
Voltage Endurance |
AC 1,000 V, 20 mA for 1 min (between charging and FG terminals) |
|
Insulation Resistance |
DC 500 V, 10 MΩ or more (between charging and FG terminals) |
|
Surrounding Air Temperature |
0 to 50 ℃ |
|
Storage Temperature |
-20 to +60 ℃ |
|
Ambient Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Storage Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Dust |
0.1 mg/m³ or less (non-conductive levels) |
|
Pollution Degree |
For use in Pollution Degree 2 environment |
|
Atmosphere |
Free of corrosive gases |
|
Air Pressure (altitude range) |
800 to 1,114 hPa (2,000 m above sea level or less) |
|
Vibration Resistance |
IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (100 min) |
|
Concussion Resistance |
IEC/EN61131-2 compliant, 147 m/s², X, Y, Z directions for 3 times |
|
Noise Immunity |
Noise Voltage: 1,000 Vp-p, Pulse Duration: 1 µs, Rise Time: 1 ns, (via noise simulator) |
|
Electrostatic Discharge Immunity |
Contact Discarge Method: 6kV (IEC/EN61000-4-2 Level 3) |
|
Grounding |
Functional grounding: Grounding resistance of 100Ω, 2mm² or thicker wire, or your country's applicable standard. (Same for FG and SG terminals) |
|
Structure |
Equivalent to IP65f NEMA #250 TYPE 4X/13 (on the front panel when properly installed in an enclosure)*6 |
|
Installation Configuration |
Embedded panel |
|
Cooling Method |
Natural air circulation |
|
Weight Approx. |
1 kg [2.2 lb] or less (display unit only) |
|
External Dimensions |
W167.5 x H135 x D78 mm [W6.59 x H5.31 x D2.87 in.] |
|
Panel Cut Dimensions |
W156 x H123.5 mm [W6.14 x H4.86 in.], Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]*7 |
-
*6 The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the GP unit's level of resistance is equivalent to these standards, oils that should have no effect on the GP can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the GP's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the GP and separate protection measures are suggested., Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the GP be sure to confirm the type of conditions that will be present in the GP's operating environment., If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.
-
*7 Regarding dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.].
External Dimensions / Interfaces
Panel Cut-out
|
|
|
|
|
|
|
|
|
Specification of LT3301-L1-D24-K
LT-3301L SinkOutput type
Model: LT3301-L1-D24-K
Monochrome LCD (16 Shades) / QVGA
Functional Specification
|
Display Type |
STN Color LCD |
|
Display Size |
5.7" |
|
Resolution |
320 x 240 pixels (QVGA) |
|
Dot pitch |
W0.36 x H0.36 mm [W0.01 x H0.01 in.] |
|
Effective Display Area |
W117.2 x H88.4 mm [W4.61 x H3.48 in.] |
|
Display Colors |
4,096 Colors |
|
Backlight |
White LED (User nonreplaceable parts. Factory replacement required.) |
|
Brightness Control |
8 Levels (Adjusted with the touch panel) |
|
Contrast Control |
8 Levels (Adjusted with the touch panel) |
|
Backlight Service Life |
50,000 hrs. or more (continuous operation at 25℃ before backlight brightness decreases to 50%) |
|
Language Fonts |
Japanese: 6,962 (JIS Standards 1 & 2) (including 607 non-kanji characters), ANK: 158 (Korean fonts, Simplified Chinese and Traditional Chinese fonts are downloadable. |
|
Character Sizes |
Standard font: 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts, Stroke font: 6 to 127 pixel fonts, Image font: 8 to 72 pixel fonts |
|
Font Sizes |
Standard font: Width can be expanded up to 8 times. Height can be expanded up to 8 times.*1 |
|
Text |
8 x 8 dots |
40 char. x 30 rows |
|
8 x 16 dots |
40 char. x 15 rows |
|
16 x 16 dots |
20 char. x 15 rows |
|
32 x 32 dots |
10 char. x 7 rows |
|
Control Memory |
Variable Area |
SRAM 64 KB (uses lithium battery) |
|
Program Area |
FLASH EPROM 132 KB |
|
Number of Step |
Equivalent to 15,000 steps*2 |
|
Application Memory |
FLASH EPROM 6 MB*3 |
|
Data Backup |
SRAM 128 KB (Lithium battery for backup memory) |
|
Clock Accuracy |
±65 sec/month (deviation at room temperature and power is OFF)*4 |
|
Touch Panel Type |
Resistive Film (analog) |
|
Touch Panel Resolution |
1,024 x 1,024 |
|
Touch Panel Service Life |
1,000,000 times or more |
|
Interface |
Serial (COM1) |
RS-232C/422/485, Asynchronous Transmission, Data Length: 7 or 8 bit, Parity: none, Even or Odd, Stop Bit: 1 or 2 bit, Data Transmission Speed: 2,400 bps to 115.2 kbps, Connector: D-Sub9 (plug) |
|
Ethernet (LAN) |
IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX, Connector: Modular jack (RJ-45) x 1 |
|
USB (TYPE-A) |
Conforms to USB1.1 (TYPE-A) x 1, Power Supply Voltage: DC 5 V ±5 %, Output Current: 500 mA or less, Communication Distance: 5 m or less |
|
AUX/Expansion Unit |
Communication Expansion Unit x 1*5 |
|
Control |
DIO (Source Type) |
16-Point Input Sink Source, , 16-Point Output Source, Connector: 38pin |
-
*1 Other font sizes can be set up with the Editor software.
-
*2 Up to 60,000 steps can be converted in software. However, this reduces internal memory capacity (for screen data) by 1 MB.
-
*3 Capacity available for user application.
-
*4 Depending on the operating temperature and age of unit, the clock can deviate from -380 to +90 sec/month. For systems where this level of deviation is a problem, the user should monitor and make adjustments when required.
-
*5 EX Module and Communication Expansion Unit cannot be used at the same time.
General Specification
|
International Safety Standards |
|
|
Rated Input Voltage |
DC 24 V |
|
Input Voltage Limits |
DC 19.2 to 28.8 V |
|
Allowable Voltage Drop |
3 ms or less |
|
Power Consumption |
27 W or less |
|
In-Rush Current |
30 A or less |
|
Voltage Endurance |
AC 1,000 V, 20 mA for 1 min (between charging and FG terminals) |
|
Insulation Resistance |
DC 500 V, 10 MΩ or more (between charging and FG terminals) |
|
Surrounding Air Temperature |
0 to 50 ℃ |
|
Storage Temperature |
-20 to +60 ℃ |
|
Ambient Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Storage Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Dust |
0.1 mg/m³ or less (non-conductive levels) |
|
Pollution Degree |
For use in Pollution Degree 2 environment |
|
Atmosphere |
Free of corrosive gases |
|
Air Pressure (altitude range) |
800 to 1,114 hPa (2,000 m above sea level or less) |
|
Vibration Resistance |
IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (100 min) |
|
Concussion Resistance |
IEC/EN61131-2 compliant, 147 m/s², X, Y, Z directions for 3 times |
|
Noise Immunity |
Noise Voltage: 1,000 Vp-p, Pulse Duration: 1 µs, Rise Time: 1 ns, (via noise simulator) |
|
Electrostatic Discharge Immunity |
Contact Discarge Method: 6kV (IEC/EN61000-4-2 Level 3) |
|
Grounding |
Functional grounding: Grounding resistance of 100Ω, 2mm² or thicker wire, or your country's applicable standard. (Same for FG and SG terminals) |
|
Structure |
Equivalent to IP65f NEMA #250 TYPE 4X/13 (on the front panel when properly installed in an enclosure)*6 |
|
Installation Configuration |
Embedded panel |
|
Cooling Method |
Natural air circulation |
|
Weight Approx. |
1 kg [2.2 lb] or less (display unit only) |
|
External Dimensions |
W167.5 x H135 x D78 mm [W6.59 x H5.31 x D2.87 in.] |
|
Panel Cut Dimensions |
W156 x H123.5 mm [W6.14 x H4.86 in.], Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]*7 |
-
*6 The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the GP unit's level of resistance is equivalent to these standards, oils that should have no effect on the GP can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the GP's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the GP and separate protection measures are suggested., Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the GP be sure to confirm the type of conditions that will be present in the GP's operating environment., If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.
-
*7 Regarding dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.].
External Dimensions / Interfaces
Panel Cut-out
|
|
|
|
|
|
|
|
|
Specification of LT3300-L1-D24-K
LT-3300L SinkOutput type
Model: LT3300-L1-D24-K
Monochrome LCD (16 Shades) / QVGA
Functional Specification
|
Display Type |
STN Color LCD |
|
Display Size |
5.7" |
|
Resolution |
320 x 240 pixels (QVGA) |
|
Dot pitch |
W0.36 x H0.36 mm [W0.01 x H0.01 in.] |
|
Effective Display Area |
W117.2 x H88.4 mm [W4.61 x H3.48 in.] |
|
Display Colors |
4,096 Colors |
|
Backlight |
White LED (User nonreplaceable parts. Factory replacement required.) |
|
Brightness Control |
8 Levels (Adjusted with the touch panel) |
|
Contrast Control |
8 Levels (Adjusted with the touch panel) |
|
Backlight Service Life |
50,000 hrs. or more (continuous operation at 25℃ before backlight brightness decreases to 50%) |
|
Language Fonts |
Japanese: 6,962 (JIS Standards 1 & 2) (including 607 non-kanji characters), ANK: 158 (Korean fonts, Simplified Chinese and Traditional Chinese fonts are downloadable. |
|
Character Sizes |
Standard font: 8 x 8, 8 x 16, 16 x 16 and 32 x 32 pixel fonts, Stroke font: 6 to 127 pixel fonts, Image font: 8 to 72 pixel fonts |
|
Font Sizes |
Standard font: Width can be expanded up to 8 times. Height can be expanded up to 8 times.*1 |
|
Text |
8 x 8 dots |
40 char. x 30 rows |
|
8 x 16 dots |
40 char. x 15 rows |
|
16 x 16 dots |
20 char. x 15 rows |
|
32 x 32 dots |
10 char. x 7 rows |
|
Control Memory |
Variable Area |
SRAM 64 KB (uses lithium battery) |
|
Program Area |
FLASH EPROM 132 KB |
|
Number of Step |
Equivalent to 15,000 steps*2 |
|
Application Memory |
FLASH EPROM 6 MB*3 |
|
Data Backup |
SRAM 128 KB (Lithium battery for backup memory) |
|
Clock Accuracy |
±65 sec/month (deviation at room temperature and power is OFF)*4 |
|
Touch Panel Type |
Resistive Film (analog) |
|
Touch Panel Resolution |
1,024 x 1,024 |
|
Touch Panel Service Life |
1,000,000 times or more |
|
Interface |
Serial (COM1) |
RS-232C/422/485, Asynchronous Transmission, Data Length: 7 or 8 bit, Parity: none, Even or Odd, Stop Bit: 1 or 2 bit, Data Transmission Speed: 2,400 bps to 115.2 kbps, Connector: D-Sub9 (plug) |
|
Ethernet (LAN) |
IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX, Connector: Modular jack (RJ-45) x 1 |
|
USB (TYPE-A) |
Conforms to USB1.1 (TYPE-A) x 1, Power Supply Voltage: DC 5 V ±5 %, Output Current: 500 mA or less, Communication Distance: 5 m or less |
|
AUX/Expansion Unit |
Communication Expansion Unit x 1*5 |
|
Control |
DIO (Source Type) |
16-Point Input Sink Source, , 16-Point Output Source, Connector: 38pin |
-
*1 Other font sizes can be set up with the Editor software.
-
*2 Up to 60,000 steps can be converted in software. However, this reduces internal memory capacity (for screen data) by 1 MB.
-
*3 Capacity available for user application.
-
*4 Depending on the operating temperature and age of unit, the clock can deviate from -380 to +90 sec/month. For systems where this level of deviation is a problem, the user should monitor and make adjustments when required.
-
*5 EX Module and Communication Expansion Unit cannot be used at the same time.
General Specification
|
International Safety Standards |
|
|
Rated Input Voltage |
DC 24 V |
|
Input Voltage Limits |
DC 19.2 to 28.8 V |
|
Allowable Voltage Drop |
3 ms or less |
|
Power Consumption |
27 W or less |
|
In-Rush Current |
30 A or less |
|
Voltage Endurance |
AC 1,000 V, 20 mA for 1 min (between charging and FG terminals) |
|
Insulation Resistance |
DC 500 V, 10 MΩ or more (between charging and FG terminals) |
|
Surrounding Air Temperature |
0 to 50 ℃ |
|
Storage Temperature |
-20 to +60 ℃ |
|
Ambient Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Storage Humidity |
10 to 90 % RH (Wet bulb temperature: 39 ℃ or less - no condensation.) |
|
Dust |
0.1 mg/m³ or less (non-conductive levels) |
|
Pollution Degree |
For use in Pollution Degree 2 environment |
|
Atmosphere |
Free of corrosive gases |
|
Air Pressure (altitude range) |
800 to 1,114 hPa (2,000 m above sea level or less) |
|
Vibration Resistance |
IEC/EN61131-2 compliant, 5 to 9 Hz Single amplitude 3.5 mm [0.14 in.], 9 to 150 Hz Fixed acceleration: 9.8 m/s², X, Y, Z directions for 10 cycles (100 min) |
|
Concussion Resistance |
IEC/EN61131-2 compliant, 147 m/s², X, Y, Z directions for 3 times |
|
Noise Immunity |
Noise Voltage: 1,000 Vp-p, Pulse Duration: 1 µs, Rise Time: 1 ns, (via noise simulator) |
|
Electrostatic Discharge Immunity |
Contact Discarge Method: 6kV (IEC/EN61000-4-2 Level 3) |
|
Grounding |
Functional grounding: Grounding resistance of 100Ω, 2mm² or thicker wire, or your country's applicable standard. (Same for FG and SG terminals) |
|
Structure |
Equivalent to IP65f NEMA #250 TYPE 4X/13 (on the front panel when properly installed in an enclosure)*6 |
|
Installation Configuration |
Embedded panel |
|
Cooling Method |
Natural air circulation |
|
Weight Approx. |
1 kg [2.2 lb] or less (display unit only) |
|
External Dimensions |
W167.5 x H135 x D78 mm [W6.59 x H5.31 x D2.87 in.] |
|
Panel Cut Dimensions |
W156 x H123.5 mm [W6.14 x H4.86 in.], Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]*7 |
-
*6 The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the GP unit's level of resistance is equivalent to these standards, oils that should have no effect on the GP can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the GP's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the GP and separate protection measures are suggested., Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the GP be sure to confirm the type of conditions that will be present in the GP's operating environment., If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.
-
*7 Regarding dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.].
External Dimensions / Interfaces
Panel Cut-out
|
|
|
|
|
 |
|
|
Please be acknowledged of the following terms of use before you use our download service. Download of any file signifies your agreement to the terms of use.
Terms of Use |
|
1. |
Digital shall retain all intellectual property rights in the files that Digital provides for this service. |
|
2. |
Who, uses or plans to use Digital's products, may download and use any file. |
|
3. |
Reproduction, disclosure, re-publication, assignment, lease, decompilation, modification, falsification or reuse of any file that Digital provides for this service shall be prohibited.
However, for manual PDFs, samples, BMP images and CAD files, you may reprint, dupulicate, quote a part of the content or the whole on your company's specification sheets, or instruction manuals for built-in products. Also you may change the layout of the content. |
|
4. |
This download service is provided through the Internet. Please acknowledge that Digital provides no guarantee of the condition at the time of provision, the availability of access and the condition of use concerning this service before you use this service. |
|
5. |
Not all of the Product CAD Data Download of Digital products are provided in this service. Please acknowledge prior to using this service that the Product CAD Data of certain products might not be provided. |
|
6. |
Please use this service at your own risk. |
Notices: |
|
1. |
Files are subject to deletion, or modification of the contents or specifications without notice. |
|
2. |
Please confirm that the downloading file size completely accords with the downloaded file size. |
|
3. |
If the file sizes do not match, delete the file without decompressing (executing) and then download the same file once again. |
LT3000 Series
2D CAD file (DXF) |
|
- |
As a DXF file is an unstable file, data compatibility is not perfect.Reading data might be imperfect depending on CAD software you use. |
|
- |
The downloaded file is a self-decompressing file. Double-click on it, and the DXF file will be unfolded. |
|
- |
Digital has confirmed that it's possible to read the DXF file above via the CAD software below.
Company name Auto Desk
CAD software name AutoCAD LT 2000i
|
|
|
|
|
|
|
