PFXSP5600WAD

Standard product information

Family

HMI

Series

SP5000 Series

Size

12" Wide

Model

PFXSP5600WAD

Global Code

PFXSP5600WAD

Product Features

12" Wide DC (Advanced Display)

Repair Status

✔ (Maintenance service is available, able to be maintained.)

Display specifications

Display type

TFT Color LCD

Display size

12.1"

Resolution

1,280 x 800 pixels (WXGA)

Auto scaling

Not equipped

Effective display area

W261.12 x H163.2 mm [W10.28 x H6.43 in.]

Display colors

262,144 colors

Backlight

White LED (Not user replaceable. When replacement is required, contact your local distributor.)

Backlight service life

50,000 hrs. or more (each in continuous operation at 25 °C [77 °F] before backlight brightness decreases to 50%)

Brightness control

0 to 100 (Adjusted with touch panel or software)

Brightness sensor

Not equipped

Touch panel type

Resistive Film (analog)

Touch panel resolution

1,024 x 1,024

Touch panel lifetime

1,000,000 times or more

Electrical specifications

Rated input voltage

12 to 24 Vdc

Input voltage limits

10.8 to 28.8 Vdc

Allowable voltage drop

12 Vdc: 1.25 ms or less
24 Vdc: 5 ms or less

Power consumption

Max. 11.5 W
Backlight adjusted (20%): 6 W or less
Backlight OFF (Stand-by mode): 2.5 W or less*1

In-rush current

30 A or less

Noise immunity

Noise Voltage : 1,000 Vp-p
Pulse Duration : 1 µs
Rise Time : 1 ns
(via noise simulator)

Voltage endurance

1,000 Vac, 20 mA for 1 minute (between power terminal and FG terminals)

Insulation resistance

500 Vdc, 10 MΩ or more (between power terminal and FG terminals)

*1Power consumption for Display Module only

Environmental specifications

International safety standards

Surrounding air temperature

0 to 60 °C [32 to 140 °F]

Storage temperature

-20 to +60 °C [-4 to 140 °F]

Ambient humidity

10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] max. - no condensation)

Storage humidity

10 to 90 % RH (Wet bulb temperature: 39 °C [102.2 °F] max. - no condensation)

Dust

0.1 mg/m3 (10-7 oz/ft3) or less (non-conductive levels)

Pollution degree

For use in Pollution Degree 2 environment

Corrosive gases

Free of corrosive gases

Air pressure (altitude range)

800 to 1,114 hPa (2,000 m [6,561 ft.] above sea level or less)

Vibration resistance

IEC/EN 61131-2 compliant
5 to 9 Hz single amplitude 3.5 mm [0.14 in.]
9 to 150 Hz fixed acceleration: 9.8 m/s2
X, Y, Z directions for 10 cycles (approx. 100 min.)

Concussion resistance

IEC/EN 61131-2 compliant 147 m/s2, X, Y, Z directions for 3 times

Electrostatic discharge immunity

Contact Discharge Method: 6 kV
Air Discharge Method: 8 kV
(IEC/EN61000-4-2 Level 3)

Structural specifications

Grounding

Functional grounding: Grounding resistance of 100 Ω, 2 mm2 (AWG 14) or thicker wire, or your country’s applicable standard (same for FG and SG terminals).

Cooling method

Natural air circulation

Structure

IP66F, IP67F, Type 4X (indoor use only)/13*2

External dimensions

W308.5 x H230.5 x D67 mm [W12.15 x H9.07 x D2.64 in.]

Panel cut-out dimensions

W295 x H217 mm [W11.61 x H8.54 in.]
Panel thickness area: 1.6 to 5 mm [0.06 to 0.2 in.]*3

Weight

3 kg [6.62 lb] or less*4

*2The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the standards shown in the specification. Even though the unit's level of resistance is equivalent to these standards, oils that should have no effect on the unit can possibly harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere to the unit for long periods of time. If the unit's front face protection sheet becomes peeled off, these conditions can lead to the ingress of oil into the unit and separate protection measures are suggested. Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel's plastic cover. Therefore, prior to installing the unit, be sure to confirm the type of conditions that will be present in the unit's operating environment. If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the panel, the original level of the protection cannot be guaranteed. To maintain the original protection level, be sure to replace the installation gasket regularly.

*3For dimensional tolerance, everything +1/-0 mm [+0.04/-0 in.] and R in angle are below R3 [R0.12 in.]. Even if the installation wall thickness is within the recommended range for the "Panel Cut Dimensions", depending on wall's material, size, and installation location of GP unit and other devices, the installation wall could warp. To prevent warping, the installation surface may need to be strengthened.

*4Display module only.